Bananenstecker im 90-Grad-Winkel VCELINK

初めて知ったパーツに驚き。（物知らずだった私） アンプとスピーカーを壁際に設置ができて最高です。 更に、音質も改善されて大変満足しています。

The socket end of these will accept a male banana plug if you remove the plastic coating and remove the set screws. You might want to wrap them in electrical tape to prevent the adjacent adapters from shorting out by touching.

These are nice and heavy-duty, and are very easy to hook up to any wire using a small flat screwdriver - you insert the wire a fair length into the end and then tighten both of the screws - one near the end and another closer to the plug. It will take a pretty heavy gauge wire and seems it could handle quite a bit of current.

Used these behind a couch where I have very little space and they work great. Regular banana plugs would fall out of wall connector. Will probably buy more to change out some of the other plugs. These are well made and worked very well

First this review is of my positive experience it’s not meant to argue or put down someone’s negative experience. I was a little skeptical about these based on a couple of the negative reviews, but figured if they’re junk I’ll return them. I’m very happy I bought these. I am a retired audio engineer and have worked with pretty much any cable or connectors made. Price, these are $1.12 each before tax I saw them from as low as .85ea in bulk to stupid expensive. The ones I received are very well made I tried to pull them apart and couldn’t. I installed these on Monster 12 gauge speaker wire and they fit perfect. One review stated caution on heavier than 14g but these easily handled the 10g I tested just to see. Bear in mind the wire gauge is always the same but the insulation thickness can vary depending on the manufacturer. The insulating sleeve just barely went over the wire insulation as the Monster wire has really thick insulation, had to put a little dish soap to get it to slide on. Yes the insulating sleeves are hard to get off the connectors if you pull on them, if you push them off with your thumb nail they slide right off. The set screws seem to hold well, if you’re worried they may loosen over time put a tiny bit of Tightlock or silicone adhesive on the threads it will hold it tight but you can still unscrew it with a screwdriver if need be. I would purchase these again if needed and would recommend them to anyone needing a few, if you need a lot I’d look for the bulk packages. Aloha

These banana plugs are great. I used them for all speakers to reduce stress on speaker terminals and save space. Paired with InstallGear 14 Gauge AWG Oxygen-Free Speaker Wire with zero issues. There was enough space to easily take proper-sized 12 Gauge wire. Banana plug fit is snug, I had zero issues connecting them the first time and disconnecting from speakers several times during installation. For those who are using banana plugs for the first time don't panic - they ARE supposed to go tight for the first time since you are slightly compressing the ribs for a precise match with speaker/wall terminals. Measured electric resistance and it's extremely low comparable to solid copper connectors. No issues with conductivity. I installed a total of 18 of these plugs for my setup and had absolutely no issues with screws or assembly. It's NOT EASY to slide plastic sleeves off if you are pulling them directly - slide them off in a circular motion instead while pulling metal assembly out.

質感等は価格なり。 実際の使用では特に問題なしです。ケーブル固定ネジ、バナナの止まり具合も上々。 L形は絶縁カバーあった方が安心。ケーブル根元の保護としてもいい感じになります。 リピートしたいと思います。

These are strong, however, they should be insulated all the way to the banana plug. I use these for replacement on VOM that some with weak banana plugs that fail to stay in the hole.

I used these in setting up an additional stereo system in my house. These connectors were very easy to install and work just as advertised with my speakers and receiver. They have a good, quality feel to them.

I bought these right angle banana plug connectors to replace the standard straight in plugs I had used for my home stereo connection. The Vcelink product looks gold-plated and they worked well, providing the sought after strain relief. The mounting tube accepts the bare wire and the connection is secured by two flush mount screws that are quite small - you will need a jewelers screwdriver to torque them down. Once secured, you pull the plastic boot up and over and you are good to plug in and go. These Vcelink plugs accepted my 14 gauge speaker wire quite easily. The plug in effort took a little more force than I anticipated but they snapped in quite snug. I would only caution against using these plugs with wire heavier than 14. I had no issue with shorting or inadvertent contact.

These were way better than the VCELINK straight banana connectors I bought previously. These are heft and have two screws for holding the wiring in place and ensuring a solid connection. HINT: Use a hair dryer or heat gun for 5 seconds or so to make the factory plastic covers pliable enough to slide off. Really like these connectors.

I had just bought a new Klipsch Center speaker for my home theater system and needed (2) 90-degree banana plugs. I decided on VCELINK plugs, but really only needed two not eight plugs. I'll find a use for the extra six someday, but the price was good and they fit nice and tight. You have to gently force them in, at first I thought they were the wrong size, but they just fit tight as they should. I'm glad I bought these nice heavy-quality plugs.

The plugs are of good quality and reasonably priced. However, I couldn't plug them into either my amp or my speakers initially because the plugs are too big. At first I thought I bought the wrong sized plugs, but after I pressed down the springs on the plugs using a pair of plier then they fit right into my speakers and amp without problem.

It works. There's no noticable improvement or distortion vs hardwired, my speakers are front ported and the new place necessitates them being very close to a wall. The 90 degree clips are great for this.